Dura-Crown
Device Facts
| Record ID | K261356 |
|---|---|
| Device Name | Dura-Crown |
| Applicant | Hangzhou SHINING3D Dental Technology Co., Ltd. |
| Product Code | EBF · Dental |
| Decision Date | Apr 27, 2026 |
| Decision | SESE |
| Submission Type | Special |
| Regulation | 21 CFR 872.3690 |
| Device Class | Class 2 |
| Attributes | 3rd-Party Reviewed |
Indications for Use
Dura-Crown is indicated as an indirect restorative for both anterior and posterior restorations, including occlusal surfaces. Dura-Crown is used for fabricating permanent restorations such as inlays, onlays, veneers, full crown and bridge restorations. Dura-Crown can also be used for the fabrication of artificial teeth and temporary crowns & bridges.
Device Story
Dura-Crown is a liquid photo-curable methacrylate-based resin used for professional dental restoration fabrication. Operated by dental professionals using SHINING3D printers (AccuFab-D1s/C1s) and post-curing units (FabCure2); the device transforms liquid resin into solid dental structures via free radical polymerization triggered by photoinitiators and UV light curing. The process involves automated layer-by-layer printing followed by post-curing. The resulting restorations (inlays, onlays, veneers, crowns, bridges, artificial teeth) are used by clinicians to restore dental function and aesthetics. The device benefits patients by providing durable, custom-fit dental prosthetics.
Clinical Evidence
No clinical data. Bench testing only. Performance verified against ISO 4049:2019, ISO 10477:2020, and ISO 22112:2017. Biocompatibility verified per ISO 10993-1:2018 and ISO 7405:2018. Flexural strength meets ≥120MPa requirement.
Technological Characteristics
Methacrylate-based polymer resin; photo-curable via UV light. Materials: (meth)acrylate oligomers/monomers, photo-initiators, fillers, pigments. Standards: ISO 4049, ISO 10477, ISO 22112, ISO 10993-1, ISO 7405. Non-sterile. Shelf-life: 2 years. Compatible with AccuFab-D1s/C1s printers and FabCure2 post-curing unit.
Indications for Use
Indicated for patients requiring indirect dental restorations (anterior/posterior, occlusal surfaces), including permanent inlays, onlays, veneers, full crowns, bridges, artificial teeth, and temporary crowns/bridges. Contraindicated in patients with known allergies to ingredients, such as acrylates.
Regulatory Classification
Identification
Tooth shade resin material is a device composed of materials such as bisphenol-A glycidyl methacrylate (Bis-GMA) intended to restore carious lesions or structural defects in teeth.
Predicate Devices
- Dura-Crown (K253053)
Submission Summary (Full Text)
{0}
FDA U.S. FOOD & DRUG ADMINISTRATION
April 27, 2026
Hangzhou SHINING3D Dental Technology Co., Ltd.
% Dave Yungvirt
CEO
Third Party Review Group, LLC
7 Giralda Farms, Suite 120a
Madison, New Jersey 07940
Re: K261356
Trade/Device Name: Dura-Crown
Regulation Number: 21 CFR 872.3690
Regulation Name: Tooth shade resin material
Regulatory Class: Class II
Product Code: EBF, EBG, PZY
Dated: April 24, 2026
Received: April 24, 2026
Dear Dave Yungvirt:
We have reviewed your section 510(k) premarket notification of intent to market the device referenced above and have determined the device is substantially equivalent (for the indications for use stated in the enclosure) to legally marketed predicate devices marketed in interstate commerce prior to May 28, 1976, the enactment date of the Medical Device Amendments, or to devices that have been reclassified in accordance with the provisions of the Federal Food, Drug, and Cosmetic Act (the Act) that do not require approval of a premarket approval application (PMA). You may, therefore, market the device, subject to the general controls provisions of the Act. Although this letter refers to your product as a device, please be aware that some cleared products may instead be combination products. The 510(k) Premarket Notification Database available at https://www.accessdata.fda.gov/scripts/cdrh/cfdocs/cfpmn/pmn.cfm identifies combination product submissions. The general controls provisions of the Act include requirements for annual registration, listing of devices, good manufacturing practice, labeling, and prohibitions against misbranding and adulteration. Please note: CDRH does not evaluate information related to contract liability warranties. We remind you, however, that device labeling must be truthful and not misleading.
If your device is classified (see above) into either class II (Special Controls) or class III (PMA), it may be subject to additional controls. Existing major regulations affecting your device can be found in the Code of Federal Regulations, Title 21, Parts 800 to 898. In addition, FDA may publish further announcements concerning your device in the Federal Register.
U.S. Food & Drug Administration
10903 New Hampshire Avenue
Silver Spring, MD 20993
www.fda.gov
{1}
K261356 - Dave Yungvirt
Page 2
Additional information about changes that may require a new premarket notification are provided in the FDA guidance documents entitled "Deciding When to Submit a 510(k) for a Change to an Existing Device" (https://www.fda.gov/media/99812/download) and "Deciding When to Submit a 510(k) for a Software Change to an Existing Device" (https://www.fda.gov/media/99785/download).
Your device is also subject to, among other requirements, the Quality Management System Regulation (QMSR) (21 CFR Part 820), which includes, but is not limited to, ISO 13485 clause 7.3 (Design controls), ISO 13484 clause 8.3 (Nonconforming product), and ISO 13485 clause 8.5 (Corrective and preventative action). Please note that regardless of whether a change requires premarket review, the QMSR requires device manufacturers to review and approve changes to device design and production (ISO 13485 clause 7.3 and 21 CFR 820.70) and document changes and approvals in the Medical Device File (21 CFR 820.181).
Please be advised that FDA's issuance of a substantial equivalence determination does not mean that FDA has made a determination that your device complies with other requirements of the Act or any Federal statutes and regulations administered by other Federal agencies. You must comply with all the Act's requirements, including, but not limited to: registration and listing (21 CFR Part 807); labeling (21 CFR Part 801); medical device reporting (reporting of medical device-related adverse events) (21 CFR Part 803) for devices or postmarketing safety reporting (21 CFR Part 4, Subpart B) for combination products (see https://www.fda.gov/combination-products/guidance-regulatory-information/postmarketing-safety-reporting-combination-products); good manufacturing practice requirements as set forth in the Quality Management System Regulation (QMSR) (21 CFR Part 820) for devices or current good manufacturing practices (21 CFR Part 4, Subpart A) for combination products; and, if applicable, the electronic product radiation control provisions (Sections 531-542 of the Act); 21 CFR Parts 1000-1050.
All medical devices, including Class I and unclassified devices and combination product device constituent parts are required to be in compliance with the final Unique Device Identification System rule ("UDI Rule"). The UDI Rule requires, among other things, that a device bear a unique device identifier (UDI) on its label and package (21 CFR 801.20(a)) unless an exception or alternative applies (21 CFR 801.20(b)) and that the dates on the device label be formatted in accordance with 21 CFR 801.18. The UDI Rule (21 CFR 830.300(a) and 830.320(b)) also requires that certain information be submitted to the Global Unique Device Identification Database (GUDID) (21 CFR Part 830 Subpart E). For additional information on these requirements, please see the UDI System webpage at https://www.fda.gov/medical-devices/device-advice-comprehensive-regulatory-assistance/unique-device-identification-system-udi-system.
Also, please note the regulation entitled, "Misbranding by reference to premarket notification" (21 CFR 807.97). For questions regarding the reporting of adverse events under the MDR regulation (21 CFR Part 803), please go to https://www.fda.gov/medical-devices/medical-device-safety/medical-device-reporting-mdr-how-report-medical-device-problems.
For comprehensive regulatory information about medical devices and radiation-emitting products, including information about labeling regulations, please see Device Advice (https://www.fda.gov/medical-devices/device-advice-comprehensive-regulatory-assistance) and CDRH Learn (https://www.fda.gov/training-and-continuing-education/cdrh-learn). Additionally, you may contact the Division of Industry and Consumer Education (DICE) to ask a question about a specific regulatory topic. See the DICE website (https://www.fda.gov/medical-devices/device-advice-comprehensive-regulatory-
{2}
K261356 - Dave Yungvirt
Page 3
assistance/contact-us-division-industry-and-consumer-education-dice) for more information or contact DICE by email (DICE@fda.hhs.gov) or phone (1-800-638-2041 or 301-796-7100).
Sincerely,
MICHAEL E. ADJODHA -S
Michael E. Adjodha, MChE, RAC, CQIA
Assistant Director
DHT1B: Division of Dental and ENT Devices
OHT1: Office of Ophthalmic, Anesthesia, Respiratory, ENT, and Dental Devices
Office of Product Evaluation and Quality
Center for Devices and Radiological Health
Enclosure
{3}
FORM FDA 3881 (8/23)
Page 1 of 1
PSC Publishing Services (301) 443-6740
EF
| DEPARTMENT OF HEALTH AND HUMAN SERVICES Food and Drug Administration Indications for Use | Form Approved: OMB No. 0910-0120 Expiration Date: 07/31/2026 See PRA Statement below. |
| --- | --- |
| 510(k) Number (if known) K261356 | |
| Device Name Dura-Crown | |
| Indications for Use (Describe) Dura-Crown is indicated as an indirect restorative for both anterior and posterior restorations, including occlusal surfaces. Dura-Crown is used for fabricating permanent restorations such as inlays, onlays, veneers, full crown and bridge restorations. Dura-Crown can also be used for the fabrication of artificial teeth and temporary crowns & bridges. | |
| Type of Use (Select one or both, as applicable) ☑ Prescription Use (Part 21 CFR 801 Subpart D) ☐ Over-The-Counter Use (21 CFR 801 Subpart C) | |
| CONTINUE ON A SEPARATE PAGE IF NEEDED. | |
| This section applies only to requirements of the Paperwork Reduction Act of 1995. *DO NOT SEND YOUR COMPLETED FORM TO THE PRA STAFF EMAIL ADDRESS BELOW.* | |
| The burden time for this collection of information is estimated to average 79 hours per response, including the time to review instructions, search existing data sources, gather and maintain the data needed and complete and review the collection of information. Send comments regarding this burden estimate or any other aspect of this information collection, including suggestions for reducing this burden, to: Department of Health and Human Services Food and Drug Administration Office of Chief Information Officer Paperwork Reduction Act (PRA) Staff PRAStaff@fda.hhs.gov | |
| "An agency may not conduct or sponsor, and a person is not required to respond to, a collection of information unless it displays a currently valid OMB number." | |
{4}
K261356
# 510(k) Summary
## I Submitter
Submitter Name: Hangzhou SHINING3D Dental Technology Co., Ltd.
Submitter Address: 9-5-2, Tri-River Valley, Wenyan Street, Xiaoshan, Hangzhou, Zhejiang, 311258, China
Registration Number: 3026312357
Budget Number: Yang Jiachen
Contact person: Regulatory Affairs Supervisor
+86-19829816259
yangjiachen@shining3d.com
Date Prepared: 24 April, 2026
## II Device
Trade Name of Device: Dura-Crown
Classification Name(s): Tooth shade resin material
Model: CB21-A1/CB21-A2/CB21-A3/CB21-B1
Regulation number: 21 CFR 872.3690
Regulatory class: Class II
Product Code: EBF, EBG, PZY
Review Panel: Dental
1 / 9
{5}
2 / 9
## III Predicate Device
Trade name: Dura-Crown
Classification Name(s): Tooth shade resin material
Regulation number: 21 CFR 872.3690
Regulatory class: Class II
Product code: EBF, EBG, PZY
Submitter Name: Hangzhou SHINING3D Dental Technology Co., Ltd.
510(k) number: K253053
## IV Device description
The product should be used in combination with SHINING3D printer. The product is a liquid photo-curable material, which is produced by free radical polymerization of oligomers triggered by a photoinitiator contained in the resin. Automated printing of the resin in multiple layers, each light-cured before adding next layer, are post cured in the cure device. The product is intended exclusively for professional dental work.
## V Indications for use
Dura-Crown is indicated as an indirect restorative for both anterior and posterior restorations, including occlusal surfaces. Dura-Crown is used for fabricating permanent restorations such as inlays, onlays, veneers, full crown and bridge restorations. Dura-Crown can also be used for the fabrication of artificial teeth and temporary crowns & bridges.
{6}
VI Available model
| Model | Color | Specification |
| --- | --- | --- |
| CB21-A1 | A1 | 0.5kg/bottle; Nano |
| CB21-A2 | A2 | |
| CB21-A3 | A3 | |
| CB21-B1 | B1 | |
VII Comparison to predicate devices
{7}
| Item | Subject device | Predicate device | Comparison with Changes |
| --- | --- | --- | --- |
| Product Name | Dura-Crown | Dura-Crown | Same, No changes |
| 510(k) Number | | K253053 | N/A |
| Classification name | Tooth shade resin material | Tooth shade resin material | Same, No changes |
| Product Code | EBF, EBG, PZY | EBF, EBG, PZY | Same, No changes |
| Device Classification | Class II | Class II | Same, No changes |
| Specification | 0.5kg/bottle | 0.5kg/bottle, Nano | New specification added |
| Submitter Name | Hangzhou SHINING3D Dental Technology Co., Ltd. | Hangzhou SHINING3D Dental Technology Co., Ltd. | Same, No changes |
{8}
| Item | Subject device | Predicate device | Comparison with Changes |
| --- | --- | --- | --- |
| Indication for Use/Intended Use | Dura-Crown is indicated as an indirect restorative for both anterior and posterior restorations, including occlusal surfaces. Dura-Crown is used for fabricating permanent restorations such as inlays, onlays, veneers, full crown and bridge restorations. Dura-Crown can also be used for the fabrication of artificial teeth and temporary crowns & bridges. | Dura-Crown is indicated as an indirect restorative for both anterior and posterior restorations, including occlusal surfaces. Dura-Crown is used for fabricating permanent restorations such as inlays, onlays, veneers, full crown and bridge restorations. Dura-Crown can also be used for the fabrication of artificial teeth and temporary crowns & bridges. | Same, No changes |
| Technology | 3D liquid (light-cured) print resin for dental CAD/CAM | 3D liquid (light-cured) print resin for dental CAD/CAM | Same, No changes |
5 / 9
{9}
| Item | Subject device | Predicate device | Comparison with Changes |
| --- | --- | --- | --- |
| Chemical Description | (Meth)acrylate oligomers and monomers, photo-initiator, fillers, additives and pigments. | (Meth)acrylate oligomers and monomers, photo-initiator, fillers, additives and pigments. | Same, No changes |
| Equipment | 3D Printer:AccuFab-D1s/C1sPost-curingUnit:FabCure2 | 3D Printer:AccuFab-D1s/C1sPost-curingUnit:FabCure23D printer with post-curing function:Ceramix-Nano | New supporting equipment added |
| Packaging | The specification of 0.5kg/bottle is packaged in a separate inner packing box containing a black plastic bottle.Each outer packaging contains six inner boxes. | The specification of 0.5kg/bottle is packaged in a separate inner packing box containing a black plastic bottle.Each outer packaging contains six inner boxes.The specification of Nano has content of 5g, 8g, 26g, 3 Unit in a pack, it is packaged in a plastic conta containing 3 | New packaging added |
{10}
| Item | Subject device | Predicate device | Comparison with Changes |
| --- | --- | --- | --- |
| | | Nano cartridges. Each outer packaging contains a plastic conta. And a content of of 65g, 1 Unit in a pack, it is packaged in a plastic conta containing 1 Nano cartridges. Each outer packaging contains a plastic conta.Also, there is a outer packaging box(transportation packaging) for Nano conta. | |
| Contraindication, warning | Do not use the product in case of a known allergy to one or more ingredients(such as acrylate). | Do not use the product in case of a known allergy to one or more ingredients(such as acrylate). | Same, No changes |
| Material Type | Methacrylate-based polymer resin | Methacrylate-based polymer resin | Same, No changes |
| Material Shades | Common VITA-shades | Common VITA-shades | Same, No changes |
{11}
| Item | Subject device | Predicate device | Comparison with Changes |
| --- | --- | --- | --- |
| Biocompatible | Yes | Yes | Same, No changes |
| Sterile | Non-sterile | Non-sterile | Same, No changes |
| Curing Method | UV Light | UV Light | Same, No changes |
| Shelf-Life | 2 years | 2 years | Same, No changes |
| Performance Testing | ISO 4049:2019 | ISO 4049:2019 | Same, No changes |
| | ISO 10477:2020 | ISO 10477:2020 | |
| | ISO 22112:2017 | ISO 22112:2017 | |
| Flexural strength | ≥120MPa | ≥120MPa | Same, No changes |
| Biocompatibility | ISO 10993-1:2018 | ISO 10993-1:2018 | Same, No changes |
| Testing | ISO 7405:2018 | ISO 7405:2018 | |
{12}
VIII Changes description
In response to commercial demand, the changes were implemented under design control procedures: the introduction of a new "Nano" product specification, which involves a new packaging configuration, and the qualification of a new supporting 3D printing device.
We conducted a design review and risk analysis (per ISO 14971) to assess the impact of these changes. The risk assessment confirmed that the change in bottle size and associated packaging does not alter the material formulation, curing properties, or chemical composition of the resin itself, thus presenting no new hazards related to material safety or device performance. Consequently, the plan focused on performance testing using the new printer and the stability of new packaging which should demonstrate that the changes in container size and printing platform do not adversely affect the safety or effectiveness of the final medical device.
IX Conclusion
The specification expansion for "Nano", packaging optimization, and supporting equipment extension changes involved in this application have not altered the device's core formulation, manufacturing process, intended use, indications for use, or the foundation of safety and effectiveness.
All changes have undergone adequate verification and validation, demonstrating substantial equivalence to the marketed predicate device.
9 / 9
