CoLink Plating System, Fracture and Correction System, RTS Implant System, NeoSpan Compression Staple System

K190385 · In2bones USA, LLC · HRS · Aug 8, 2019 · Orthopedic

Device Facts

Record IDK190385
Device NameCoLink Plating System, Fracture and Correction System, RTS Implant System, NeoSpan Compression Staple System
ApplicantIn2bones USA, LLC
Product CodeHRS · Orthopedic
Decision DateAug 8, 2019
DecisionSESE
Submission TypeTraditional
Regulation21 CFR 888.3030
Device ClassClass 2
AttributesTherapeutic, Pediatric

Intended Use

The In2Bones USA LLC, CoLink™ Plating System is indicated for stabilization and fixation of fractures, revision procedures, joint fusion, osteotomies and reconstruction of the small bones in the hand, wrist, foot and ankle in both pediatric and adult patients. The In2Bones USA LLC, CoLink™ Afx Plating System is indication and fixation of fractures and osteotomies in the ankle, including tibia and fibula, in both pediatric and adult patients. The In2Bones USA LLC, Fracture and Correction System plates and screws are intended to treat fractures, fusions, osteotomies and non-unions of the 5th metatarsal. The Fracture and Correction System lag screws are intended to be used as stand-alone bone screws, or in a plate-screw system for internal bone fixation for bone fractures, fusions, osteotomies and non-unions of various bones, including humerus, radius, ulna, tibia, calcaneus, fibula, and small bones (metatarsals, and phalanges). The In2Bones NeoSpan® Compression Staple Implant w/instruments is indicated for hand and foot bone fragments, osteotomy fixation and joint arthrodesis. The RTS® Flexible 1ST MPJ Implant w/Grommets is intended for use in the treatment of: Hallux limitus or hallux rigidus; Painful rheumatoid arthritis; Hallux abducto valgus associated with arthritis; Unstable or painful joint from previous surgery. The RTS® Lesser MTP Implant is intended for use in the treatment of: Partial or complete dislocation of the lesser metatarsophalangeal joint; Pain associated with either rheumatoid or osteoarthritis; Repair of unsuccessful arthroplasties of the lesser metatarsophalangeal joint; Stiffness at the lesser metatarsophalangeal joint associated with joint disease; Hammertoe deformity where the proximal phalanx is dorsally located on the metatarsal in a fixed contracture state.

Device Story

System comprises orthopedic implants including plates, screws, compression staples, and silicone toe implants; used for bone fixation, fusion, and reconstruction in extremities. Implants are surgically implanted by orthopedic surgeons in clinical/OR settings to stabilize bone fragments or replace joints. CoLink systems use titanium/PEEK; Fracture/Correction system uses titanium; NeoSpan uses superelastic Nitinol; RTS system uses silicone elastomer. Device provides mechanical support to hold bones in position during healing. This submission specifically updates labeling to include MR conditional status. No changes to device geometry, materials, or indications compared to predicates.

Clinical Evidence

Bench testing only. MR safety testing was conducted according to ASTM F2052, ASTM F2213, ASTM F2182, and ASTM F2119 on worst-case configurations to validate MR conditional labeling.

Technological Characteristics

Materials: ASTM F136 Ti6Al4V, ASTM F2026 PEEK, ASTM F2063 Nitinol, and NuSil Med 4755 silicone elastomer. Components include plates, screws, staples, and silicone toe implants. MR conditional status validated via ASTM standards.

Indications for Use

Indicated for pediatric and adult patients requiring stabilization, fixation, or reconstruction of small bones (hand, wrist, foot, ankle), including fractures, osteotomies, joint fusions, non-unions, and specific joint pathologies (hallux limitus/rigidus, rheumatoid/osteoarthritis, dislocations, hammertoe).

Regulatory Classification

Identification

Single/multiple component metallic bone fixation appliances and accessories are devices intended to be implanted consisting of one or more metallic components and their metallic fasteners. The devices contain a plate, a nail/plate combination, or a blade/plate combination that are made of alloys, such as cobalt-chromium-molybdenum, stainless steel, and titanium, that are intended to be held in position with fasteners, such as screws and nails, or bolts, nuts, and washers. These devices are used for fixation of fractures of the proximal or distal end of long bones, such as intracapsular, intertrochanteric, intercervical, supracondylar, or condylar fractures of the femur; for fusion of a joint; or for surgical procedures that involve cutting a bone. The devices may be implanted or attached through the skin so that a pulling force (traction) may be applied to the skeletal system.

Predicate Devices

Reference Devices

Related Devices

Submission Summary (Full Text)

{0}------------------------------------------------ August 8, 2019 Image /page/0/Picture/1 description: The image contains the logos of the Department of Health & Human Services and the Food and Drug Administration (FDA). The Department of Health & Human Services logo is on the left, featuring a stylized human figure. To the right of that is the FDA logo, which includes the letters "FDA" in a blue square, followed by the words "U.S. FOOD & DRUG ADMINISTRATION" in blue text. In2Bones USA, LLC Christine Scifert VP of Quality and Regulatory 6000 Poplar Ave, Suite 115 Memphis, Tennessee 38119 Re: K190385 Trade/Device Name: CoLink Plating System, Fracture and Correction System, RTS Implant System, NeoSpan Compression Staple System Regulation Number: 21 CFR 888.3030 Regulation Name: Single/Multiple Component Metallic Bone Fixation Appliances And Accessories Regulatory Class: Class II Product Code: HRS, HWC, KWH, JDR Dated: July 9, 2019 Received: July 10, 2019 Dear Christine Scifert: We have reviewed your Section 510(k) premarket notification of intent to market the device referenced above and have determined the device is substantially equivalent (for the indications for use stated in the enclosure) to legally marketed predicate devices marketed in interstate commerce prior to May 28, 1976, the enactment date of the Medical Device Amendments, or to devices that have been reclassified in accordance with the provisions of the Federal Food, Drug, and Cosmetic Act (Act) that do not require approval of a premarket approval application (PMA). You may, therefore, market the device, subject to the general controls provisions of the Act. Although this letter refers to your product as a device, please be aware that some cleared products may instead be combination products. The 510(k) Premarket Notification Database located at https://www.accessdata.fda.gov/scripts/cdrh/cfdocs/cfpmn/pmn.cfm identifies combination product submissions. The general controls provisions of the Act include requirements for annual registration, listing of devices, good manufacturing practice, labeling, and prohibitions against misbranding and adulteration. Please note: CDRH does not evaluate information related to contract liability warranties. We remind you, however, that device labeling must be truthful and not misleading. If your device is classified (see above) into either class II (Special Controls) or class III (PMA), it may be subject to additional controls. Existing major regulations affecting your device can be found in the Code of Federal Regulations, Title 21, Parts 800 to 898. In addition, FDA may publish further announcements concerning your device in the Federal Register. Please be advised that FDA's issuance of a substantial equivalence determination does not mean that FDA has made a determination that your device complies with other requirements of the Act or any Federal statutes and regulations administered by other Federal agencies. You must comply with all the Act's {1}------------------------------------------------ requirements, including, but not limited to: registration and listing (21 CFR Part 807); labeling (21 CFR Part 801); medical device reporting of medical device-related adverse events) (21 CFR 803) for devices or postmarketing safety reporting (21 CFR 4, Subpart B) for combination products (see https://www.fda.gov/combination-products/guidance-regulatory-information/postmarketing-safety-reportingcombination-products); good manufacturing practice requirements as set forth in the quality systems (OS) regulation (21 CFR Part 820) for devices or current good manufacturing practices (21 CFR 4, Subpart A) for combination products; and, if applicable, the electronic product radiation control provisions (Sections 531-542 of the Act); 21 CFR 1000-1050. Also, please note the regulation entitled, "Misbranding by reference to premarket notification" (21 CFR Part 807.97). For questions regarding the reporting of adverse events under the MDR regulation (21 CFR Part 803), please go to https://www.fda.gov/medical-device-safety/medical-device-reportingmdr-how-report-medical-device-problems. For comprehensive regulatory information about mediation-emitting products, including information about labeling regulations, please see Device Advice (https://www.fda.gov/medicaldevices/device-advice-comprehensive-regulatory-assistance) and CDRH Learn (https://www.fda.gov/training-and-continuing-education/cdrh-learn). Additionally, you may contact the Division of Industry and Consumer Education (DICE) to ask a question about a specific regulatory topic. See the DICE website (https://www.fda.gov/medical-device-advice-comprehensive-regulatoryassistance/contact-us-division-industry-and-consumer-education-dice) for more information or contact DICE by email (DICE@fda.hhs.gov) or phone (1-800-638-2041 or 301-796-7100). Sincerely, Shumaya Ali, MPH Assistant Director DHT6C: Division of Restorative, Repair, and Trauma Devices OHT6: Office of Orthopedic Devices Office of Product Evaluation and Quality Center for Devices and Radiological Health Enclosure List of Cleared Devices in K190385 {2}------------------------------------------------ ### List of Cleared Devices in K190385 - 1. CoLink® Plating System / CoLink® View Plating System / CoLink® Afx Plating System - 2. Fracture and Correction System (5MS™ and CoLag™) - 3. NeoSpan® Compression Staple Implant with Instruments - 4. RTS® Silicone Toe System {3}------------------------------------------------ 510(k) Number (if known) K190385 Device Name CoLink® Plating System / CoLink® View Plating System / CoLink® Afx Plating System Indications for Use (Describe) The In2Bones USA LLC, CoLink™ Plating System is indicated for stabilization and fixation of fractures, revision procedures, joint fusion, osteotomies and reconstruction of the small bones in the hand, wrist, foot and ankle in both pediatric and adult patients. The In2Bones USA LLC, CoLink™ Afx Plating System is indication and fixation of fractures and osteotomies in the ankle, including tibia and fibula, in both pediatric and adult patients. | Type of Use (Select one or both, as applicable) | | |---------------------------------------------------------------------------------------------------------------------|--------------------------------------------------------------------------------------------------------------------| | <div> <span> <span style="font-size: 16px;">☑</span> Prescription Use (Part 21 CFR 801 Subpart D) </span> </div> | <div> <span> <span style="font-size: 16px;">☐</span> Over-The-Counter Use (21 CFR 801 Subpart C) </span> </div> | ### CONTINUE ON A SEPARATE PAGE IF NEEDED. This section applies only to requirements of the Paperwork Reduction Act of 1995. #### *DO NOT SEND YOUR COMPLETED FORM TO THE PRA STAFF EMAIL ADDRESS BELOW.* The burden time for this collection of information is estimated to average 79 hours per response, including the time to review instructions, search existing data sources, gather and maintain the data needed and complete and review the collection of information. Send comments regarding this burden estimate or any other aspect of this information collection, including suggestions for reducing this burden, to: > Department of Health and Human Services Food and Drug Administration Office of Chief Information Officer Paperwork Reduction Act (PRA) Staff PRAStaff@fda.hhs.gov {4}------------------------------------------------ 510(k) Number (if known) K190385 Device Name Fracture and Correction System (5MSTM and CoLag™) Indications for Use (Describe) The In2Bones USA LLC, Fracture and Correction System plates and screws are intended to treat fractures, fusions, osteotomies and non-unions of the 5th metatarsal. The Fracture and Correction System lag screws are intended to be used as stand-alone bone screws, or in a plate-screw system for internal bone fixation for bone fractures, fusions, osteotomies and non-unions of various bones, including humerus, radius, ulna, tibia, calcaneus, fibula, and small bones (metatarsals, and phalanges). Type of Use (Select one or both, as applicable) | <span></span> | <input checked="true" type="checkbox"/> Prescription Use (Part 21 CFR 801 Subpart D) | |---------------|--------------------------------------------------------------------------------------| | <span></span> | <input type="checkbox"/> Over-The-Counter Use (21 CFR 801 Subpart C) | ### CONTINUE ON A SEPARATE PAGE IF NEEDED. This section applies only to requirements of the Paperwork Reduction Act of 1995. ### *DO NOT SEND YOUR COMPLETED FORM TO THE PRA STAFF EMAIL ADDRESS BELOW.* The burden time for this collection of information is estimated to average 79 hours per response, including the time to review instructions, search existing data sources, gather and maintain the data needed and complete and review the collection of information. Send comments regarding this burden estimate or any other aspect of this information collection, including suggestions for reducing this burden, to: > Department of Health and Human Services Food and Drug Administration Office of Chief Information Officer Paperwork Reduction Act (PRA) Staff PRAStaff@fda.hhs.gov {5}------------------------------------------------ 510(k) Number (if known) K190385 Device Name NeoSpan® Compression Staple Implant with Instruments Indications for Use (Describe) The In2Bones NeoSpan® Compression Staple Implant w/instruments is indicated for hand and foot bone fragments, osteotomy fixation and joint arthrodesis. | Type of Use (Select one or both, as applicable) | | |------------------------------------------------------------------------------------------------------------------------------------------------|--------------------------------------------------------------------------------------------------------------------------------| | <span style="white-space: nowrap;"> <input checked="true" type="checkbox"/> Prescription Use (Part 21 CFR 801 Subpart D) </span> | <span style="white-space: nowrap;"> <input type="checkbox"/> Over-The-Counter Use (21 CFR 801 Subpart C) </span> | ### CONTINUE ON A SEPARATE PAGE IF NEEDED. This section applies only to requirements of the Paperwork Reduction Act of 1995. ### *DO NOT SEND YOUR COMPLETED FORM TO THE PRA STAFF EMAIL ADDRESS BELOW.* The burden time for this collection of information is estimated to average 79 hours per response, including the time to review instructions, search existing data sources, gather and maintain the data needed and complete and review the collection of information. Send comments regarding this burden estimate or any other aspect of this information collection, including suggestions for reducing this burden, to: > Department of Health and Human Services Food and Drug Administration Office of Chief Information Officer Paperwork Reduction Act (PRA) Staff PRAStaff@fda.hhs.gov {6}------------------------------------------------ 510(k) Number (if known) K190385 Device Name RTS® Silicone Toe System Indications for Use (Describe) The RTS® Flexible 1ST MPJ Implant w/Grommets is intended for use in the treatment of: - · Hallux limitus or hallux rigidus - Painful rheumatoid arthritis - Hallux abducto valgus associated with arthritis - · Unstable or painful joint from previous surgery The RTS® Lesser MTP Implant is intended for use in the treatment of: - · Partial or complete dislocation of the lesser metatarsophalangeal joint - · Pain associated with either rheumatoid or osteoarthritis - · Repair of unsuccessful arthroplasties of the lesser metatarsophalangeal joint - · Stiffness at the lesser metatarsophalangeal joint associated with joint disease - · Hammertoe deformity where the proximal phalanx is dorsally located on the metatarsal in a fixed contracture state. | Type of Use (Select one or both, as applicable) | | |-------------------------------------------------|--| |-------------------------------------------------|--| X | Prescription Use (Part 21 CFR 801 Subpart D) | | Over-The-Counter Use (21 CFR 801 Subpart C) ### CONTINUE ON A SEPARATE PAGE IF NEEDED. This section applies only to requirements of the Paperwork Reduction Act of 1995. ### *DO NOT SEND YOUR COMPLETED FORM TO THE PRA STAFF EMAIL ADDRESS BELOW.* The burden time for this collection of information is estimated to average 79 hours per response, including the time to review instructions, search existing data sources, gather and maintain the data needed and complete and review the collection of information. Send comments regarding this burden estimate or any other aspect of this information collection, including suggestions for reducing this burden, to: > Department of Health and Human Services Food and Drug Administration Office of Chief Information Officer Paperwork Reduction Act (PRA) Staff PRAStaff@fda.hhs.gov {7}------------------------------------------------ ## 510(k) Summary # In2Bones USA, LLC – MR Labeling July 9, 2019 | Company: | In2Bones USA, LLC<br>6000 Poplar Ave, Suite 115<br>Memphis, TN 38119<br>901-260-7931 | |--------------------|-------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------| | Company Contact: | Christine Scifert | | Trade Name: | CoLink® Plating System<br>CoLink® View Plating System<br>CoLink® Afx Plating System<br>RTS® Silicone Toe System<br>NeoSpan® Compression Staple System with Instruments<br>Fracture and Correction System | | Common Name: | Plate, Fixation, Bone<br>Screw, Fixation, Bone<br>Prosthesis, Toe, Constrained, Polymer<br>Staple, Fixation, Bone | | Classification: | II | | Regulation Number: | 888.3030 - Single/multiple component metallic bone fixation appliances<br>and accessories<br>888.3040 - Smooth or threaded metallic bone fixation fastener<br>888.3720 - Toe joint polymer constrained prosthesis | | Panel: | 87-Orthopedic | | Product Code(s): | HRS, HWC, KWH, IDR | ### Device Description: The In2Bones CoLink® Plating System / CoLink® View Plating System is a system of plates and screws and surgical instruments used to treat fracture and reconstruction of the extremities. The CoLink® Afx Plating System is a system of plates and surgical instruments used to treat traumatic fractures and osteotomies of the ankle. The products are made of ASTM F 136 Titanium {8}------------------------------------------------ 6Aluminum 4Vanadium Alloy (Ti6Al4V) and the CoLink® View System has inserts made of ASTM F 2026 Poly Ether Ether Ketone (PEEK). The Fracture and Correction System consists of the 5MS® Plate and Screw System and the CoLag® cannulated lag screws used to treat fracture and reconstruction of the bones of the extremities. The products are made of ASTM F 136 Titanium 6Aluminum 4Vanadium Alloy (Ti6A14V). The RTS® Lesser MTP Implant System is a double stem silicone implant which is placed into the intramedullary canals of the first metatarsal and proximal phalangeal bones of the forefoot. The RTS® Flexible 1* MPJ Implant w/Grommets System is a flexible silicone great toe implant. Titanium grommets are also available for use in the first metatarsal (only) if the option is desired by the surgeon. The implant is used in the treatment of arthritis of the metatarsophalangeal joint. The implants are made from silicone elastomer NuSil Med 4755 from NuSil. The In2Bones NeoSpan® Compression Staple Implant is a super elastic compression staple made of superelastic Nitinol (ASTM F2063). The devices are available in multiple sizes. The implant is designed to hold bones together until healing occurs. ### Indications for Use: ### CoLink® Plating System / CoLink® View Plating System / CoLink® Afx Plating System The In2Bones USA LLC, CoLink™ Plating System is indicated for stabilization and fixation of fractures, revision procedures, joint fusion, osteotomies and reconstruction of the small bones in the hand, wrist, foot and ankle in both pediatric and adult patients. The In2Bones USA LLC, CoLink™ Afx Plating System is indicated for stabilization and fixation of fractures and osteotomies in the ankle, including tibia and fibula, in both pediatric and adult patients. ### RTS® Silicone Toe System The RTS® Flexible 1ST MPJ Implant w/Grommets is intended for use in the treatment of: - Hallux limitus or hallux rigidus - · Painful rheumatoid arthritis - · Hallux abducto valgus associated with arthritis - · Unstable or painful joint from previous surgery The RTS® Lesser MTP Implant is intended for use in the treatment of: - · Partial or complete dislocation of the lesser metatarsophalangeal joint - · Pain associated with either rheumatoid or osteoarthritis - · Repair of unsuccessful arthroplasties of the lesser metatarsophalangeal joint - · Stiffness at the lesser metatarsophalangeal joint associated with joint disease - · Hammertoe deformity where the proximal phalanx is dorsally located on the metatarsal in a fixed contracture state. ### NeoSpan® Compression Staple Implant with Instruments {9}------------------------------------------------ The In2Bones NeoSpan® Compression Staple Implant w/instruments is indicated for hand and foot bone fragments, osteotomy fixation and joint arthrodesis. ### Fracture and Correction System (5MS™ and CoLag™) The In2Bones USA LLC, Fracture and Correction System plates and screws are intended to treat fractures, fusions, osteotomies and non-unions of the 5th metatarsal. The Fracture and Correction System lag screws are intended to be used as stand-alone bone screws, or in a plate-screw system for internal bone fixation for bone fractures, fusions, osteotomies and non-unions of various bones, including humerus, radius, ulna, tibia, calcaneus, fibula, and small bones (metacarpals, metatarsals, and phalanges). ### Substantial Equivalence: The subject components were demonstrated to be substantially equivalent to the following systems previously cleared by the FDA: - Primary Predicate: - K182402 CoLink View Plating System o - . Secondary Predicates: - K180377 Fracture and Correction System o - K181113 CoLink Afx Plating System O - O K173491 – RTS Lesser MTP Implant System - K172300 CoLink View Plating System O - K170518 In2Bones Fracture and Correction System O - K163293 CoLink Plating System O - K161426 NeoSpan Compression Staple Implant with Instruments o - K153609 RTS Flexible 1 MPJ Implant with Grommets O - Reference Predicates: - K160553 DePuy Synthes MR Conditional Labeling O - K172975 DePuy Synthes MR Conditional Labeling O - K152631 MPO Total Knee Systems MR Labeling O The subject In2Bones USA, LLC product families have been demonstrated to be substantially equivalent to the previously cleared devices identified above as the products are identical in indications, materials and geometry. The only modification is the addition of MR labeling. ### Performance Testing: MR Testing per ASTM Standards (ASTM F2052, ASTM F2213, ASTM F2182 and ASTM F2119) was conducted on worst case products to cover all In2Bones product families. ### Conclusion Based on the test results and the comparison to the predicate devices, the subject device is determined to be substantially equivalent to the predicate devices.
Innolitics
510(k) Summary
Decision Summary
Classification Order
Enter a record ID and click Load to view the document.
100%